Webbing artwork and repeat length
The repeat must work with the cut length. Mark the first logo, seam allowance and acceptable cut zone so assembly does not leave a half logo at the end.
Content updated
In this guide
Key choices for your project
Measure the repeat from one identical point to the next, not from the edge of a cropped image. Include a scale bar or dimension on the artwork. For cut straps, map the repeat against finished length so important text does not disappear into the seam allowance.
- Repeat measured between identical points
- Finished cut length
- Seam allowance and hidden area
A repeat that looks complete on screen can leave half a logo at every cut end
Imagine a cropped design file showing one logo centred between two decorative marks. Its image boundary is treated as the repeat, although the left and right edges are not identical pattern points. When production tiles the file, spacing changes at every join. The woven roll looks acceptable, but the specified strap length places the first logo inside one seam allowance and cuts the final wordmark in half. Moving the pattern after sampling also changes every product position.
Define repeat length between identical pattern points and add a dimension or scale reference to the controlled design data. Map logo sequence, orientation, first-pattern position, finished cut length, seam allowances, folds and hidden regions together. Generate a full-length layout for each piece code, mark permitted cut zones and weave or print a physical trial. Approve the actual-size roll and assembled cut piece, then control both design revision and repeat phase.
Approve design data and repeat as one production layout, measured between identical points and proven against finished cut length, seams, folds and permitted cut zones.
Map repeat remainders across every cut length
For each SKU, divide the usable cut length by the proposed repeat and show the remainder at the start and finish. This exposes where a logo phase will drift between short and long straps. Choose whether the unused remainder is absorbed in a hidden return, shared between ends or controlled by positioned cutting.
- Repeat remainder shown for each finished length
- Named location that absorbs the unused pattern length
Build version and scale checks into the artwork file
Put the revision, finished tape width, repeat dimension and one known scale mark inside the released file. Convert or package fonts and keep colour layers named by function. Production can then detect an accidentally resized or older file before sampling, while purchasing can trace exactly which graphic belongs to the approved physical strip.
- Revision and scale mark visible in the released file
- Approved physical strip linked to the artwork filename
Connect controlled design data to repeat and cut-piece geometry
The record prevents cropped-image edges from becoming false repeat boundaries and links the patterned roll to every finished visible window.
Swipe to see all columns ↔
| Field | What to record | How to confirm |
|---|---|---|
| Design-data control | Source format, dimensions or scale bar, colour references, fonts or outlined text, revision, owner and date | Open approved source at actual size |
| Repeat definition | Length between named identical pattern points, widthwise position, orientation and any alternating sequence | Overlay consecutive repeats |
| Webbing construction | Printed or woven route, fibre, yarn or ink colours, width, edges, approved face, lot and sample code | Inspect physical production trial |
| Cut-piece geometry | Piece code, finished and cut lengths, first-pattern position, seams, folds, hardware and hidden regions | Create full-length 1:1 layout |
| Cutting rules | Permitted cut zones, allowable motif interruption, phase tolerance, waste rule and treatment of roll joins | Mark production cutting guide |
| Approval references | Actual-size roll section, assembled piece, viewing conditions, accepted revision, repeat and approver | Seal signed matched set |
Manufacturing feasibility and tolerances depend on print or weave construction; the buyer’s authorized design owner must approve any simplification or motif interruption.
Download specification worksheet ↓Prove the repeat on every finished cut length
Prepare dimensioned design data
Supply scalable source data with physical dimensions, colour references, orientation and controlled text rather than relying on a cropped preview.
Measure identical repeat points
Choose a recognizable pattern point and measure to its next identical occurrence, then tile several repeats to verify the join.
Map each finished piece
Place repeat, first motif, cut length, seam allowances, folds and hidden zones on a full-size layout for every code.
Trial and approve physical output
Inspect actual-size roll and assembled pieces, confirm permitted cuts, then retain the signed design revision and patterned samples together.
Repeat approvals that fail during cutting and assembly
Measuring a cropped image edge
A screenshot boundary may not join at an identical pattern point. Define and dimension the true repeat inside controlled source data.
Approving a roll without cut lengths
A good continuous pattern can still place text inside seams or split logos. Overlay every finished piece before approval.
Moving motifs without new revision
A small phase shift changes all cut positions and visible windows. Reissue layouts, trials and approval references after any change.
Questions before you choose
How do I choose the repeat length for a logo on webbing?
Lay the tape path over the finished product and mark cut ends, folds, seams and hardware. Set the repeat so at least the intended number of complete logos remains visible in each part. Check short sizes as well as the longest version before approval.
What dimensions must be included in a webbing artwork file?
Include finished tape width, motif width and height, repeat length, distance from both edges, face direction and a repeat origin. Mark cutting, folding and sewing zones. Supply vector artwork where possible and lock the approved scale rather than resizing it informally.
Products to start with
Open a product to see its listed specification. Custom colours, dimensions and order terms are confirmed for your project.
More product photos
Tell us what you are making
You can enquire before every detail is settled. Tell us the intended use and what you need help choosing; add dimensions or quantities if you know them.
What happens after your enquiry
We review the intended use and open specification questions first. Sample options, costs, minimum quantities and timing can then be discussed against that brief. Sending an enquiry does not place an order.
Request a relevant sample →
